dual-phase steel

英 [ˈdjuːəl feɪz stiːl] 美 [ˈduːəl feɪz stiːl]

网络  双相钢

化学



双语例句

  1. Dual-phase steel in the country's first production, with the industry's largest variety, the most complete specification.
    双相钢在全国产量第一,同行业最大,品种、规格最全。
  2. Feasibility Study of Chenggang 1780 Plant for Developing High-quality Hot-rolling Dual-phase Steel
    承钢1780开发优质热轧双相钢的可行性研究
  3. Comparison of joint performance between weld-bonding and resistance spot welding of dual-phase steel The Study of Heat Transfer Enhancement by Twisted Insert
    双相钢胶焊与电阻点焊接头性能对比分析螺旋内插件强化传热换热器的性能对比分析
  4. Effect of Martensite Volume Fraction on Deformation Dislocation Structure and Fracture for Hot Rolled Dual-Phase Steel
    马氏体体积分数对热轧双相钢形变位错结构和断裂的影响
  5. Microstructure and properties of 780 MPa grade cold rolled dual-phase steel
    780MPa级冷轧双相钢的组织与性能研究
  6. Experimental Study of 600 MPa Grade Hot-rolling Dual-Phase Steel
    600MPa级热轧双相钢的试制研究
  7. Tensile behavior and fracture characteristics of step-quenched dual-phase steel 20
    台阶淬火双相20钢的拉伸行为及断裂特征
  8. Effect of martensite volume fraction on deformation dislocation structure and fracture for hot rolled dual-phase steel of the same composition was studied by using SEM and TEM.
    文章利用SEM、TEM研究了热轧双相钢单向拉伸过程中不同变形量下的形变位错结构和断口组织特征。
  9. The effect of the finishing rolling temperature on the microstructure refinement and mechanical properties of the hot rolled dual-phase steel were studied at laboratory.
    研究了终轧温度对高强热轧双相钢组织细化和力学性能的影响。
  10. A study on plastic deformation and fracture of hot rolled dual-phase steel
    热轧双相钢塑性变形和断裂行为的研究
  11. Modeling Composition Design of Cold Rolled Hot-dip Galvanized Dual-phase Steel
    冷轧热镀锌双相钢成分设计模型化的研究
  12. The effect of hot working process on the stability of microstructure of as-hot-rolled dual-phase steel was examined.
    研究了热轧工艺对热轧态双相钢组织稳定性的影响。
  13. Retained Austenite in Dual-phase Steel
    双相钢中的残余奥氏体
  14. The research results showed that the maximum tensile strength of dual-phase steel raised with the increase of martensite content.
    研究表明,随着马氏体含量的增加,双相钢的最大拉伸强度随之增加,延伸率随着马氏体的增加而降低。
  15. The impact toughness of strain-strengthening dual-phase steel at low temperature was re searched.
    研究了形变强化双相钢的低温冲击韧度。
  16. Study on Process of Microstructure Refinement for Hot-rolled Dual-phase Steel
    热轧双相钢组织细化工艺的研究
  17. Deformation Effect on Microstructure and Mechanical Properties of Hot-Rolled Dual-Phase Steel
    变形工艺对热轧双相钢显微组织和性能的影响
  18. Study on hot-rolled dual-phase steel without Mo
    无钼热轧双相钢的研究
  19. Study on the Optimal Heat Treatment Technology of High Strength 20 Dual-phase Steel Wire
    20钢高强度双相钢丝最佳热处理工艺的研究
  20. To introduce the trial production process, the microstructure and properties of hot-rolled dual-phase steel wire rod for non-quenched and tempered fasteners with high strength.
    介绍非调质高强度紧固件用热轧双相钢盘条的试制工艺、组织和性能。
  21. Microstructure and Properties of Hot-rolled and Controlled Cooling Dual-phase Steel Wire Rod
    热轧控冷双相钢盘条的组织及性能
  22. Study on Relationship between the Torsion Moment and Martensite Content of Dual-Phase Steel
    双相碳钢动态扭矩性能和马氏体含量关系的研究
  23. Effect of Finishing Rolling Temperature on Microstructure Refinement for Hot Rolled Dual-phase Steel
    终轧温度对热轧双相钢组织细化的影响
  24. Four kinds of dual-phase steel with different morphology were developed by means of step quenching treatment routes.
    通过四种不同的分步淬火热处理工艺,相应地获得了四种不同组织的双相钢。
  25. Microstructure-properties of Controlled-rolled Microalloyed Dual-phase Steel
    控制轧制微合金双相钢的显微组织及性能
  26. To discuss the possibility producing high strength bolt and steel wire with 20 dual-phase steel.
    探讨20双相钢生产高强度螺栓和高强度钢丝的可能性。
  27. Structures and properties of hot-rolled dual-phase steel bar
    热轧棒材双相钢组织与性能
  28. Study on Texture of Low Carbon Dual-phase Steel Wire in Deep Drawing
    低碳双相钢丝在深度拉拔过程中织构形成的研究
  29. Based on the study of corrosion laws and mechanisms, the principles and methods of the alloy design and microstructure controlling were put forward, providing the experimental and theoretical basis of corrosion aspects for the new dual-phase steel design and development, process optimization, product performance.
    在综合腐蚀规律与机制研究的基础上,给定了合金设计与微观组织控制原则与方法,为新型双相钢钢种的设计开发、工艺优化、产品性能保证提供腐蚀方面的实验与理论依据。